Brasscraft Toilet Repair Manuel d'utilisateur télécharger pdf

CONE

WASHER

SHANK

WASHER

SHANK

WASHER

FLANGE

TANK

BOTTOM

THREADED

SHANK

LOCK NUT LOCK NUT

LOCK NUT

WATER

SHUT-OFF

WATER

SHUT-OFF

WATER

SHUT-OFF

WATER

SHUT-OFF

EXISTING

COUPLING

NUT

COUPLING

NUT

COUPLING

NUT

COUPLING

NUT

EXISTING

WASHER

CONE

WASHER

EXISTING

CONE

WASHER

CONE

WASHER

Brass Craft Model 2000

Anti-Siphon Fill Valve

INSTALLATION INSTRUCTIONS:

1. Shut off water supply to tank; flush toilet and remove remaining water from tank with

sponge.

2. Unthread existing coupling nut and lock nut; then detach refill tube from overflow tube.

Remove old fill valve assembly from tank. (FIG. 1)

3. Remove cone washer from center of shank washer (included in package contents) and set

aside. Place new shank washer, flat side up, onto threaded shank of new fill valve - flat

against flange. (FIG. 2)

4. Position new fill valve in tank as shown (FIG. 3). Float, connecting rod and control lever of fill

valve must NOT touch toilet tank walls. In addition, be sure that nothing interferes with float

or linkage of the fill valve.

5. To secure fill valve into position, hold body of fill valve, not the float, and thread new lock nut

onto threaded shank of fill valve. Push downward on cap while tightening the lock nut. Hand

tighten only. DO NOT OVERTIGHTEN.

6. Identify the type of water supply nosepiece of current water hookup from illustrations noted

below. If new cone washer and coupling nut are necessary, both have been supplied.

• FLAT (illustration A) - use existing coupling nut and washers. May be necessary to install new

washers (not included) to ensure a water-tight seal.

• CONE - shape w/ flange on the tube (illustration B) - use cone washer and coupling nut

supplied in package.

• CONE - shape w/ corrugated tubing (illustration C) - use existing cone washer and/or friction

ring with new coupling nut supplied. Supply tube MUST extend 1/2 IN. inside threaded shank.

CAUTION: Replace cone washer if it shows signs of brittleness or loss of pliability.

Cone washer supplied CANNOT be used in this installation - it will not provide the

proper seal. (illustration C)

• PLAIN (illustration D) - use existing friction ring with cone washer and coupling nut included in

package. Supply tube MUST extend 1/2 IN. inside threaded shank.

7. Hand tighten coupling nut. DO NOT OVERTIGHTEN. DO NOT use a wrench or similar tool

to tighten coupling nut.

CAUTION: Over tightening plastic lock nut or coupling nut may crack or damage nut or

fill valve resulting in a water leak and potential flooding.

8. Attach one end of refill tube to nipple on fill valve. Slide "S" - shaped clip onto other end of

refill tube; clip onto inside edge of overflow tube so that refill tube will discharge into overflow.

NOTE: Be certain that refill tube does not interfere with operation of float, connecting rod or

control lever. (FIG. 3)

9. Turn on water supply and allow tank to fill - fill valve will shut off when cycle is complete.

Water level should be 1" to 1-1/2" below top of overflow tube. For proper anti-siphon

operation, the Critical Level mark on fill valve, noted by a "CL" on fill valve body, MUST

be 1" above the over flow tube. If CL level is not in correct position with overflow tube;

adjust height of fill valve. See instruction #10.

OVERFLOW TUBE

(NOT INCLUDED)

CONTROL

LEVER

CAP

CONNECTING

ROD

WATER LEVEL

ADJUSTMENT

CLIP

REFILL

TUBE

THREADED

SHANK

VALVE

BODY

SHANK

WASHER

CONE WASHER

LOCK NUT

ADJUSTABLE

HEIGHT

COUPLING NUT

PARTS FOR WATER

CONNECTION

FIG. 1

FIG. 2

(A)

(B)

FIG. 3

FLOAT

CRITICAL

LEVEL

“S” CLIP

NIPPLE

FLAPPER

(KIT ONLY)

CRITICAL

LEVEL

10. ADJUST WATER LEVEL in tank to recommended height by rotating valve body 1/4-turn in

the FREE (counterclockwise) direction as noted on fill valve cap. Push down to break seals

loose as they may tend to stick.

• To RAISE the water level - pull up to desired height then rotate valve body 1/4-turn clock

wise in the LOCK direction to lock new position into place.

• To LOWER the water level - press down on valve body to desired height. Rotate valve body

1/4-turn clockwise in the LOCK direction to lock new position into place. (FIG 4)

• To FINE TUNE water level - squeeze the tabs of the float adjustment clip on the lift arm and

slide float up or down as necessary. Sliding the float UP will raise the water level; DOWN

will lower the water level. Be careful not to slide the adjustment clip off the end of the lift

arm. (FIG. 5)

11. Flush toilet and allow tank to refill to determine results of adjustments; make further

adjustments as needed.

12. Check coupling nut and lock nut for leaks. If leak appears, further tighten nuts. If leak

continues, turn off water supply and flush toilet to empty tank. Remove nut, realign washer

and retighten connections.

13. CHECK FILL VALVE FOR TROUBLE-FREE OPERATION:

• Does the fill valve shut off? If not, check…

(A) the float, connecting rod and control lever - do they operate without touching toilet tank

wall or interfere with the refill tube. If so, adjust accordingly.

(B) the flapper - is it seated properly? If not, reseat flapper into position.

see #10 to adjust water level.

• Does the tank fill? If not, check…

(A) the water supply valve - is it open? If not, turn handle of water supply counterclockwise

to open valve and allow flow of water to toilet.

(B) the refill tube - is it properly fastened to the top inside edge of the overflow tube? Are

there other components that interfere with the refill tube’s operation? Adjust accordingly.

• Does the fill valve shut off with a loud noise (water hammer)? If yes, check…

(A) the water supply valve - partially closing the water supply valve will reduce the flow rate

and eliminate the hammer sound.

FIG. 5

1. Shut off water supply to toilet and flush to remove water from tank.

2. If replacing tank-type ball, remove lift wires, ball and guide arm.

3. Remove worn flapper ball from adaptor on the overflow tube.

4. You’re ready to install your Hornet flapper.

A. Douglas Flush Valves (FIG. 6)

1. Slip the ring (FIG. 7) over the overflow tube (bulb down) until it reaches the bottom

of the tube. Adjust flapper so that bulb is centered over valve opening.

B. New style plastic flush valves (with protruding pins) (FIG. 8)

1. Ears at each side of flapper are then slipped over the protruding pins (FIG. 8) at the

base of the overflow tube.

C. Crane Flush Valves

1. Place slot on rear of flapper (FIG. 9) over protrusion in Crane tank.

5. Attach plastic chain to tank lever arm. Keep chain slack to minimum in closed position

and cut chain to length. Be sure that plastic guard is down and covers hook to avoid

chain from kinking.

6. Turn water supply on.

NOTE: Use abrasive cloth or steel wool on surface of brass flush valve opening to

remove pits, etc.

FIG. 6

FIG. 7

FIG. 8

OVER-FLOW

TUBE

LIFT

WIRES

TANK

BALL

VALVE

OPENING

GUIDE

ARM

OVER-FLOW

TUBE

RING

BULB

VALVE

OPENING

OVER-FLOW

TUBE

PINS

EAR

Installing Hornet Flapper

Flapper included only in fill valve kit, not included in individually boxed fill valve.

Tools Needed for Installation:

• Wrench (use only to remove old nut, as needed)

• Sponge

• Scissors

CAUTION: Toilet tank drop-in cleaners can damage or severely reduce product life.

DO NOT use chlorine based toilet bowl cleaners.

LOCK INTO

POSITION

RAISE OR

LOWER FILL

VALVE

TO ADJUST HEIGHT

NOVI, MI U.S.A

FIG. 4

CUT

(FOR NEW

STYLE)

EARS

SLOT

(FOR CRANE)

CHAIN

FIG. 9

NOTCHED

OPENING

PLASTIC

GUARD

New Style Plastic

Flush Valve Installation

Douglas Flush Valve

Installation

1-1

1/2

000565

1 2

Résumé du contenu

Page 1 - Anti-Siphon Fill Valve

CONEWASHERSHANKWASHERSHANKWASHERFLANGETANKBOTTOM THREADEDSHANK LOCK NUT LOCK NUTLOCK NUTLOCK NUTWATER SHUT-OFFWATER SHUT-OFFWATER SHUT-OFFWATER SHUT-O

Page 2 - Brass Craft Modelo 2000

ARANDELA (SELLO)CÓNICAARANDELADEL VÁSTAGOARENDELADEL VÁSTAGOBRIDAFONDO DELTANQUE VÁSTAGOROSCADOTUERCO DESEGURIDADTUERCO DESEGURIDADTUERCO DESEGURIDAD

Commentaires sur ces manuels

Pas de commentaire

Brasscraft Toilet Repair Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires pour l'eau Brasscraft Toilet Repair. BrassCraft Toilet Repair User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels